The following are migrated pages from the time the Stang was being built and rebuilt. Plans changed along the way so unless you follow it all the way through it may not make sense for the end results.
08/10/2005 – Pulled fenders, pressure washed, scrapped/cleaned old sealer, grease, etc
10/01/2005 – Front suspension pulled, checking for what’s required front end wise
10/09/2005 – Steering Pulled
10/16/2005 – Few details, floor pan
10/19/2005 – Export Brace and a Couple other pics
10/20/2005 – Eport Brace Problems and Floor pan
10/21/2005 – Drivers floor Out, Export brace In
10/22/2005 – Spot weld cutting, inner fender rust, Doors off
01/02/2006 – Floor Pans Fitted (But not used in the long run)
02/12/2006 – Side Tracked on Choices
03/05/2006 – Sub Frames Installed – EFI Parts Are In
04/05/2006 – Shock Tower Parts and Rotors
06/06/2006 – Moog and More, Export Brace Update, Roller Perches
06/21/2006 – Welding Up Holes – And Rocket Man
06/24/2006 – Uber Cheap Body Dolly – New A Arms – Outside shots
07/02/2006 – Blasted! – Roller perches, Upper Arms and Bad News
07/16/2006 – Tower-Less, Sealed, Brakes and Brace
07/24/2006 – Tower back in – Test fit, tacked and partially welded
07/30/2006 – Tower welded, Smoothed, Undercoated, and Pants on Fire ?
08/10/2006 – Suspension fit test, Pedal Assembly, Brakes and more Moog
08/13/2006 – Roller Clutch Bearings – Brake/Clutch Pedal Rebuilt
08/20/2006 – Hydraulic Clutch, Vacuum Canister, and Brakes
08/28/2006 – Clutch update and Wiring, wiring, wiring…
09/03/2006 – Throttle Pedal/Cable, New Computer Location, Vent Work and Wiring Needed
Old links being migrated to new server – they do not work
5/25/2015
Engine Work, Front Springs, and
Engine Accessories 5/13/2015
Yes There is Progress! – Engine, Parts,
Tires and More 4/1/2015
Engine Wrapping Up – Seat Options 3/15/2015
Stainless Gas Tank, Radiator, Fans and
Wiring 3/8/2015
Heads, Rockers and Pushrods 3/1/2015
Clutch and Console 2/22/2015
Short Block Done – Clutch Work – Poly
Bushings – Hiding Wiring 1/25/2015
Thats a Wrap – Finalized Under Dash
Harness – Testing in the car 01/11/2015
Cluster Done, Wiring Testing, AC
Compressor Bracket 01/01/2015
Fuel, Carb and Cluster…. 11/23/2014
Brakes are Getting there – E-Brake Too 10/26/2014
Roll Out – Some Color – Some Under and Over 8/17/2014
347 Shortblock Build, Prep for Engine Bay 8/10/2014
Plan “Z” and 347 Stroker Build Finally Begins 7/11/2013
Narrow(er) 9 Inch In / On the Ground /
Rolled Out 3/20/2010
MSD 6AL/Coil, ZEX Controller and AC Work 3/14/2009
Engine Mockup / Clearance
Check / Scatter shield purchase 2/20/2008
More B-Quite / Wire Work 2/10/2008
B-Quite Continues – Picked up
a 5.0 Motor 1/21/2008
Floor Pans Done! 1/13/2008
Floor Pans Version 2 – Fuel System Stuff 5/27/2007
5/27/2007
– New Master Cylinder, 347 Stoker Kit
4/22/2007
Block and Mock
4/20/2007
B Quite / No Time / New
Twisted Wedge Heads
03/14/2007
Back to the Stang Planet –
Been buying Parts – Lower Dash Painted
01/14/2007
C&L Pipe/80mm Mass Air – Fan Review – Cleaning
Underneath
01/07/2007
GT40 Intake – 70mm Throttle Body – Drive shaft test fit
– Finished TKO Mount
01/01/2007
Test fit TKO – Built Cross
member
12/31/2006
UniSteer Rack and Pinion,
Mock Motor In
12/22/2006
Front Brakes Take II – Export Brace – Rack and Pinion
12/03/2006
Front Brakes – err Brake that
is
11/26/2006
Thinking About Wheels, Engine Hoist Deal, and Brakes
11/18/2006 Steering
Column Rebuild – SN95 Rear Disc 11/5/2006 5 Speed Time –
Tremec TKO, Shifter and more 9/17/2006 Brake Pedals and White Gauges 9/10/2006 Rotors,
Relays, and Battery Cable …and
alittle side tracked with a new small project – the “GoMo”
