Back to Stang Page69stang.gif (5918 bytes)

| HomeRobotics | HomeAutomation | Racing | 1/24 Models | Mustang | PaPa |

The Rebuild
Last Update: 05/26/15


Full Viewable Punch / ToDo List for the Car in Google Docs
5/25/2015 Engine Work, Front Springs, and Engine Accessories
5/13/2015 Yes There is Progress! - Engine, Parts, Tires and More
4/1/2015 Engine Wrapping Up - Seat Options
3/15/2015 Stainless Gas Tank, Radiator, Fans and Wiring
3/8/2015 Heads, Rockers and Pushrods
3/1/2015 Clutch and Console
2/22/2015

Short Block Done - Clutch Work - Poly Bushings - Hiding Wiring

1/25/2015 Thats a Wrap - Finalized Under Dash Harness - Testing in the car
01/11/2015 Cluster Done, Wiring Testing, AC Compressor Bracket
01/01/2015 Fuel, Carb and Cluster....
11/23/2014 Brakes are Getting there - E-Brake Too
10/26/2014 Roll Out - Some Color - Some Under and Over
8/17/2014 347 Shortblock Build, Prep for Engine Bay
8/10/2014 Plan "Z" and 347 Stroker Build Finally Begins
7/11/2013 Narrow(er) 9 Inch In / On the Ground / Rolled Out
3/20/2010 MSD 6AL/Coil, ZEX Controller and AC Work
3/14/2009 Engine Mockup / Clearance Check / Scatter shield purchase
2/20/2008 More B-Quite / Wire Work
2/10/2008 B-Quite Continues - Picked up a 5.0 Motor
1/21/2008 Floor Pans Done!
1/13/2008 Floor Pans Version 2 - Fuel System Stuff
5/27/2007 5/27/2007 - New Master Cylinder, 347 Stoker Kit
4/22/2007 Block and Mock
4/20/2007 B Quite / No Time / New Twisted Wedge Heads
03/14/2007 Back to the Stang Planet - Been buying Parts - Lower Dash Painted
01/14/2007

C&L Pipe/80mm Mass Air - Fan Review - Cleaning Underneath

01/07/2007 GT40 Intake - 70mm Throttle Body - Drive shaft test fit - Finished TKO Mount
01/01/2007 Test fit TKO - Built Cross member
12/31/2006 UniSteer Rack and Pinion, Mock Motor In
12/22/2006 Front Brakes Take II - Export Brace - Rack and Pinion
12/03/2006 Front Brakes - err Brake that is
11/26/2006

Thinking About Wheels, Engine Hoist Deal, and Brakes

11/18/2006 Steering Column Rebuild - SN95 Rear Disc
11/5/2006 5 Speed Time - Tremec TKO, Shifter and more
9/17/2006 Brake Pedals and White Gauges
9/10/2006 Rotors, Relays, and Battery Cable
...and alittle side tracked with a new small project - the "GoMo"
09/03/2006 Throttle Pedal/Cable, New Computer Location, Vent Work and Wiring Needed
08/28/2006 Clutch update and Wiring, wiring, wiring...
8/20/2006 Hydraulic Clutch, Vacuum Canister, and Brakes
8/13/2006 Roller Clutch Bearing, Brake/Clutch Rebuilt
08/10/2006 Suspension fit test, Pedal Assembly, Brakes and more Moog
7/30/2006 Tower welded, Smoothed, Undercoated, and Pants on Fire?
7/24/2006 Tower back in - Test fit, tacked and partially welded
7/16/2006 Tower-Less, Sealed, Brakes and Brace
7/2/2006 Blasted! - Roller perches, Upper Arms and Bad News
6/24/2006 Uber Cheap Body Dolly - New A Arms - Outside shots
06/21/2006 Welding up Holes and Rocket Man
06/06/2006 MOOG and More - Export Brace Update, roller perches
04/05/2006 Subframe Connectors, Shock Tower and Rotors
03/05/2006 Sub Frames Installed / EFI Parts all in
02/12/2006 Sidetracked
01/02/2006 Floor pans fitted
10/22/2005 Spot weld cutting, inner fender rust, Doors off
10/21/2005 Drivers floor Out, Export brace In
10/20/2005 Export Brace Problems and Floor pan
10/19/2005 Export Brace and a Couple other pics
10/16/2005 Few details, floor pan 
10/09/2005 Steering Pulled
10/1/2005 Front suspension pulled, checking for what's required front end wise
08/10 to 13/2005 Pulled fenders, pressure washed, scrapped/cleaned old sealer, grease, etc

[onestat.htm]